Specialist supplier · est. 1992Energy efficiency excellence
Our range of energy control solutions includes PIR sensors, daylight harvesting, dimming systems and programmable controllers. These products help reduce energy use by ensuring lights are only on when and where they are needed.
Why specify us
Sensor and controller families dim lighting to ambient daylight and switch off when areas are unoccupied.
Layering controls on top of LED can deliver further energy savings versus LED alone in suitable spaces.
Sensors and controllers integrate with both new luminaires and many existing installations — no full re-wire required.
Two-stage options deliver full output on motion and low-power dwell on unoccupancy — without on/off cycling.
Specified for this sector
A range of luminaires and controls engineered for the demands of this sector.
QUOTEThe MoviDim-RMS series is a two-way IR remote programmable line voltage switching occupancy sensor with 0-10V output for dimmable ballast or LED driver control. The sensor is capable of providing energy efficient lighting control in multiple modes with fully programmable multi-level high/low dim or EasyDIM control. EasyDIM is a state-of-the-art automatic dimming control technology, which is capable of maintaining the overall ambient light level within the preset range through a smooth, flawless continuous dimming control to the connected lighting.
Request quote
QUOTEIntegraCell is a patented daylight sensor developed to automatically switch lights on at dusk and off at dawn, providing continuous illumination through the night. Unlike standard photocells requiring the sensor head to be fitted into the body of the luminaire, the unique design of the IntegraCell, incorporating 2 photodiodes, is programmed to distinguish between daylight and LED light, enabling it to be concealed within the luminaire but still operating on daylight switching only.
Request quote
QUOTEThe Micromac-PC is an innovative motion sensor, switch on the light on detection of movement, and switch off after a hold time when there is no motion detected. The MicroMac-PC has a combined daylight sensor developed to automatically switch lights on at dusk and off at dawn, providing continuous illumination through the night. Unlike standard photocells requiring the sensor head to be fitted into the body of the luminaire, the unique design of the MicroMac-PC is programmed to distinguish between daylight and LED light, enabling it to be concealed within the luminaire but still operating on daylight switching.
Request quote
QUOTEThe MoviLux-ECO movement sensor is designed to provide automatic control of lighting, heating or ventilation loads. It detects movement using a PIR sensor and turns the load on. When an area is no longer occupied the load will switch off after an adjustable time out period. An adjustable internal light sensor provides additional energy saving in lighting applications. When an area is occupied, lighting is only switched on when the level of natural light falls below a preset level. When the sensor is first powered up the PIR sensor will always detect immediately regardless of whether the room is occupied.
Request quote
QUOTEThe operational characteristics of LED lighting and the related drivers can cause significant in-rush currents at start-up, resulting in nuisance tripping of the circuits during switching. Morgan Hope have designed the ICP-3 to interface with the distribution board lighting circuits, including but not limited to ranges of various types of Circuit Breakers or Fused Systems. The purpose of the ICP Range is to suppress the in-rush current from the LED circuits and drivers. In-rush current is a momentary surge of power which is rarely simultaneous when switching multiples of LedLite Luminaires, enabling a single ICP-3 unit to manage up to 20 fittings per circuit. The ICP protects against circuit tripping and damage to circuit breakers.
Request quote
QUOTEMicroTect is an occupancy detector system utilising Microwave technology to provide rapid response detection, with high sensitivity, where PIR technology would be restricted. It is designed to react to the slightest movement within its detection zone, even when concealed within luminaires. The MicroTect “IM” is primarily designed for location into luminaires whereas the MicroTect “SM”is primarily designed to be situated outside luminaires
Request quote
QUOTEThe MicroDim “Dimmable” Microwave Occupancy System is designed to operate with both LED and Fluorescent with 0V to 10V analogue dimming LED Drivers and dimming High Frequency Ballast, which functions on the basis of full output when movement is detected and will dim in a single stage to minimum output of the Driver/Ballast rating at approximately 10%, when the area is unoccupied. It can supplied for remote surface mount fixing or located within the housing of the luminaire and will detect through the diffuser and as such will operate on occupancy but still retain the sealed integrity of the luminaire.
Request quote
QUOTEThe MCD-PIR Movement Controlled Dimmable Lighting System is designed to operate LED or fluorescent analogue 1V to 10V dimming Ballasts or Drivers, maintaining full output during occupancy, then dimming in two stages with 50% output after 5 minutes of non-detection and an additional 40% after a further 2.5 minutes of non-detection, to remain at a constant 10% output. Any time during the time-out movement is detected, the luminaire will switch to 100% output. The MCD-PIR does not have daylight facility and whilst suitable for most areas requiring occupancy control it is especially useful in areas such as Data Centres, where moving equipment could cause nuisance switching with Microwave detection.
Request quoteShowing 8 of 9 products
Specifier resources
PDF Datasheets
Why Morgan Hope
Three decades of sector experience and a versatile supply range — all from one specialist partner.
Who we work with
A selection of the organisations we've worked with across sectors and project types.
In their words
“Working with Morgan Hope and in particular Jonathan and David throughout the Grand Arcade, Wigan LED lighting installation has been a pleasure. Their levels of communication throughout the project have been exceptional and the aftercare provided post the install has been excellent. The team deployed to complete the installation worked in a professional and efficient manner working closely with the operational team on site to minimise disruption and complete to schedule.”
Adam Richards
Area Commercial Manager, North West and Yorkshire
APCOA Parking
“The retrofit gear-tray approach saved us a six-figure capital outlay and the energy savings have been ahead of the modelled figures from month one. The Morgan Hope team specified everything around our existing pit fittings — no civil work, no re-wiring, no scaffolding.”
David Hughes
Depot Engineering Manager
Arriva Trains Wales
“Solar columns are perfect for our remote depot — no DNO application, no trenching, deployed in days. Astrid Solar has handled two British winters now and we've not had a single failed call-out. Energy bills on this site are zero.”
Daniel O'Connor
Operations Manager
Atlantic Coastal Logistics
Specification support
Our team can help you find the right lighting for your project.
